About Us
Quality
Products
Applications
Newsroom
EN

How Do Dry Screw Vacuum Pumps Work?

Source:
Publish Time:2026-11-18
Back to List

Dry screw vacuum pumps create vacuum by trapping gas between two counter-rotating screw rotors and the pump housing, moving and compressing it toward the exhaust, and discharging it. This removes gas from the connected chamber and lowers its pressure. The pumping chamber operates without an oil or liquid seal.

Understanding this mechanism helps equipment builders and process engineers evaluate where a dry screw pump fits, which utilities it needs, and how it will behave under the gas load of a real process.

What is a dry screw vacuum pump?

A dry screw vacuum pump is a positive-displacement pump. It removes gas by repeatedly enclosing volumes of gas and moving them mechanically from the inlet toward the outlet.

“Screw” describes the shape of its two rotors. “Dry” describes the pumping chamber, where no liquid is required to provide sealing or lubrication during normal operation.

Small, precisely controlled clearances separate the rotors from each other and from the housing. The drive maintains their synchronized movement so gas can be transported without normal rubbing contact between these surfaces.

The working principle: intake, compression and exhaust

1. Gas enters through the inlet

As the rotors turn, spaces formed by the rotor profiles and housing open to the inlet. Gas from the connected vacuum chamber enters these spaces and becomes enclosed as rotation continues.

The inlet connection and the piping between the chamber and pump form part of the gas path. Their dimensions and restrictions influence how effectively gas reaches the pump.

2. The rotors transport and compress the gas

Continued rotation carries the enclosed gas toward the exhaust end. The pump raises the gas pressure sufficiently for discharge into the exhaust system.

The compression pattern depends on the rotor geometry. For example, variable-pitch designs can change the available gas volume along the rotors, influencing how compression develops. Different screw profiles therefore produce different pressure, power and temperature characteristics.

3. Gas leaves through the exhaust

The gas exits through the outlet and enters the connected exhaust system. Repeated gas removal reduces chamber pressure as long as removal exceeds the gas entering or being released inside the chamber.

During a drying process, this includes vapor released from the material after much of the initial air has been removed. The pump must handle that continuing load as well as the initial chamber evacuation.

Are dry screw vacuum pumps oil-free?

Dry screw vacuum pumps do not require oil as a sealing or lubricating fluid in the pumping chamber. This is the basis of their oil-free pumping principle and helps avoid introducing sealing oil into the process gas path.

Some designs still use oil-lubricated gears or bearings in areas separated from the pumping chamber. Other arrangements differ. Buyers should check where lubricants are used, how the gas path is isolated, and which maintenance tasks apply to the selected model.

Process compatibility remains a separate consideration. The pump’s materials, seals and exhaust arrangements must suit the gases and vapors being handled.

Can a screw pump run dry?

A dry screw vacuum pump is designed to pump gases without a liquid seal in its compression chamber. In that sense, dry operation is its normal operating principle.

However, “screw pump” also describes equipment used to transfer liquids. The operating requirements of a liquid-handling twin screw pump cannot be inferred from those of a dry screw vacuum pump. Identify the pump technology and follow the instructions for the specific model.

Dry pumping also requires the utilities specified by the manufacturer. Depending on the design and process, these may include cooling water, purge gas or seal-protection gas.

Why cooling and vapor handling matter

Gas compression generates heat. Cooling controls the pump’s operating temperature, while the selected temperature range also affects how process vapors behave.

For a vapor-rich application, the goal is a suitable thermal condition for the process. Excessive cooling can encourage condensation; excessive temperature can create other operating problems. Gas composition, vapor load and the pump’s approved temperature limits all matter.

Where fitted, gas ballast introduces a suitable non-condensable gas during compression to help discharge vapor without condensation. Purge gas may serve other purposes, such as protecting seals or flushing defined parts of the system. Their locations, gas supplies and settings depend on the pump configuration.

Applications with condensable vapor, particles or liquid carryover may also need inlet protection or other process-specific arrangements. These should be considered as part of the complete vacuum system.

From working principle to pump selection

The operating principle explains how gas moves. Selecting a pump also requires matching its performance to the process.

Requirement What to check
Working pressure Read the pumping-speed curve at the pressure required by the process.
Chamber volume and cycle time Check the time needed to evacuate the actual chamber through its connected piping.
Gas and vapor load Define composition, quantity, temperature and any expected carryover.
Installation Confirm electrical supply, cooling, connections, controls and service access.
Operating cost Evaluate measured power over the duty cycle, utilities and maintenance requirements.

Ultimate pressure and operating pressure describe different conditions. Ultimate pressure is an endpoint measured under specified test conditions. Actual process pressure also depends on gas load, leakage, outgassing and restrictions in the system.

Dry screw vacuum pumping with Dacuum DP

Dacuum DP dry screw vacuum pumps use a non-contact twin-screw pumping principle, with water cooling and control-interface options for integration into industrial equipment.

For a specific application, the useful starting point is the process duty: required pressure, chamber volume, pump-down time and gas or vapor characteristics. These requirements can then be assessed against the selected model’s current pumping curve, utility requirements and configuration.

Where the duty calls for a booster, a matched Roots-and-screw arrangement can be evaluated as a complete pumping system.

Frequently asked questions

Is peak pumping speed available at every pressure?

No. Pumping speed varies with inlet pressure. Use the model’s pressure–pumping-speed curve and account for restrictions between the pump and chamber when evaluating the required duty.

Do dry screw vacuum pumps require cooling water?

Some use water cooling and others use air cooling, depending on the design. Dacuum’s DP product page specifies water cooling. Check the selected model’s utility requirements before planning the installation.

Can dry screw vacuum pumps handle water vapor?

Suitable configurations can handle vapor within defined limits. Capacity depends on the vapor load, operating temperature, ballast or purge provisions and any required inlet protection. Review the actual duty with the supplier.

When is a Roots booster useful?

A matched Roots booster can increase pumping capacity over a useful pressure range. Its backing-pump requirements, operating limits and controls must be evaluated together with the dry screw pump.

Contact Dacuum to discuss your application. Share your target pressure, chamber volume, required pump-down time, gas or vapor composition, and available utilities so the team can review a suitable pump or pumping system.


About Dacuum

Dacuum, part of DC Precision, develops and manufactures dry screw vacuum pumps and integrated vacuum systems for battery manufacturing, semiconductors, photovoltaics and other industrial applications. With a manufacturing base in Changzhou, China, the company combines R&D, precision manufacturing and application-specific engineering with commissioning and after-sales support. Dacuum works with customers to develop vacuum solutions suited to their process requirements and operating conditions. Learn more at www.dacuum.com.


Share

Technical Consulting

Accurate Q&A on Vacuum Technology | Design of Customized Working Conditions | Full Process Guidance on Selection and Adaptation